- Plant-Based Deodorant
- Water Treatment Chemicals
- Coagulant
-
Flocculant
- Polyacrylamide for Textile, Food & Process Industries
- Polyacrylamide for Oil, Gas & Drilling
- Polyacrylamide for Pulp&Paper
- Polyacrylamide for Mining & Mineral Processing
- Polyacrylamide for Sludge Dewatering
- Polyacrylamide for Water & Wastewater Clarification
- Polyacrylamide Emulsion
- Polyacrylamide Powder
- BWD-01 Water Decoloring Agent
Anionic Polyacrylamide APAM Off-White Granular Powder 20-100 Mesh for Concrete Wash Water Solids Separation CAS 9003-05-8 750kg Net Big Bag
Product Introduction
Concrete Wash Water Solids Separation buyers are usually not looking for a generic bag of PAM. They need a polymer program that fits high-pH wash water containing cement fines, sand and aggregate particles. BLUFLOC APAM is positioned on this page as a grade-selection family for that specific operating problem.
In the treatment train, BLUFLOC APAM bridges fine cementitious solids into aggregates for settling and water recovery. Because water chemistry, particle charge, shear and separator design all change the result, Bluwat recommends laboratory screening followed by a controlled plant trial rather than publishing a universal dosage or guaranteed removal rate.

Application Challenges
- High pH may fall outside the polymer solution pH shown in the TDS.
- Hydration reactions and changing cement type alter particle surfaces.
- Coarse aggregate must be removed before polymer treatment.
- Recovered water can affect concrete mix consistency and chemistry.
How BLUFLOC APAM Works
After particles have been destabilized when required, hydrated anionic polyacrylamide chains adsorb on more than one particle. This bridging mechanism increases the effective floc size and changes how the solids settle, float or drain. The selected polymer bridges fine cementitious solids into aggregates for settling and water recovery. Polymer selection must balance charge interaction, molecular weight, mixing energy and the target separator.
|
Treatment boundary: PAM does not neutralize alkaline wash water. Reuse in concrete must follow plant quality controls and applicable standards. |
Recommended Grade and Selection Guidance
Screen low, medium and higher anionic-degree grades across the 5-100% family range together with molecular-weight options in the 5-25 million range. The headline parameter is a procurement filter, while the jar test determines the practical grade.
TDS-Based Technical Specifications
| TDS item | Typical family value |
| Headline parameter | off-white 20-100 mesh granular powder |
| Product family | BLUFLOC Anionic Polyacrylamide Powder |
| Ionic charge | Anionic |
| Appearance | Off-white granular powder |
| Particle size | 20-100 mesh |
| Molecular weight | 5-25 million |
| Anionic degree | 5-100% family range |
| Solid content | 89% minimum |
| Bulk density | About 0.8 |
| Residual monomer | 0.05% maximum |
| Recommended working solution | 0.1-0.5% |
| pH of 1% aqueous solution | 6-8 |
| Storage temperature | 0-35 deg C |
| Shelf life | 2 years |
TDS note: Values describe the BLUFLOC powder family. The supplied TDS labels the degree row as 'Anionic Degree' across all columns; this document uses 'Charge Degree' for CPAM and 'Ionic Degree' for NPAM for clearer publishing. Confirm the final commercial grade by sample testing.
Application Process
- Screen out coarse aggregate and measure pH, solids and alkalinity.
- Test APAM directly in representative wash water at operating pH.
- Dose after coarse separation with controlled mixing.
- Settle or thicken solids and manage alkaline sludge safely.
- Approve recovered-water reuse through concrete quality testing.
Solution Preparation and Dosing
- Fill the make-down tank with clean water and start agitation in the 200-400 rpm TDS range.
- Add the powder slowly and evenly to avoid fish-eyes or lumps; do not dump a full bag into one point.
- Prepare a 0.1-0.5% working solution and allow about one hour for complete dissolution, subject to water quality and temperature.
- Avoid high-speed mixing after hydration because excessive shear can reduce polymer-chain performance.
- Meter the dilute solution into the selected feed point. Keep concentrated PAM separate from coagulants unless compatibility is proven.
Trial Evaluation Checklist
- Track settling velocity.
- Track clarified-water solids.
- Track sludge density.
- Track concrete quality indicators when water is reused.
- Record the untreated control, chemical sequence, mixing energy, water temperature and observations at each dose.
Product Advantages for Procurement
- Application-led grade screening for concrete wash water solids separation instead of one-grade-fits-all selling.
- Powder family covers anionic, cationic and nonionic options for comparative testing.
- TDS-grounded solid content, particle size, residual monomer, solution concentration, storage and shelf-life data.
- 25 kg bags and 750 kg net big bags support trials, distributor inventory and bulk plant consumption.
- Laboratory and technical selection support for sample screening and scale-up planning.
Packaging, Storage and Handling
Listing pack: 750 kg net big bag. The family TDS states kraft paper or PE bags with inner plastic bags, 25 kg per bag, or 750 kg net big bags. Store dry at 0-35 deg C, away from direct sunlight and moisture. The stated shelf life is two years. Use normal industrial chemical handling controls and consult the current SDS before use.
Bluwat Factory Advantages and Technical Support
Bluwat Chemicals supplies BLUFLOC polyacrylamide directly from manufacturing operations with more than 25 years of industry experience, exports to more than 80 countries, and supports OEM/customization and laboratory grade selection. For publication, the title's ISO 9001 manufacturer wording describes the supplier management-system context; confirm the current certificate and scope before listing it as an active claim.
Frequently Asked Questions
Is APAM the correct grade for concrete wash water solids separation?
It is a TDS-supported screening candidate, not a fixed prescription. Test several molecular-weight and charge options with representative water or sludge, then confirm the best grade in a plant trial.
What starting dosage should be used?
No universal plant dosage is stated. Begin with a laboratory dose series, include an untreated control, and optimize the total treatment program against clarity, separation rate, sludge behavior and cost.
How should the powder be dissolved?
Prepare a 0.1-0.5% solution by adding the powder slowly into agitated water. The TDS indicates about one hour for complete dissolution and 200-400 rpm agitation. Avoid high shear and undissolved lumps.
Can BLUFLOC PAM replace the primary coagulant or reaction chemistry?
Not automatically. PAM does not neutralize alkaline wash water. Reuse in concrete must follow plant quality controls and applicable standards. In many applications PAM is added after coagulation, precipitation, neutralization or emulsion breaking.
What information should be sent for grade selection?
Send the application, treatment flow diagram, pH, conductivity, TSS or sludge solids, current chemicals and doses, separation equipment, target water quality, and a representative sample when possible. Key trial metrics should include settling velocity, clarified-water solids, sludge density.
What packaging and storage conditions apply?
This listing uses 750 kg net big bag. The TDS also allows 25 kg kraft/PE bags with inner plastic bags or 750 kg net big bags. Store dry at 0-35 deg C, protect from sunlight and moisture, and use within the two-year shelf life.
Request a Sample and Treatment Recommendation
|
CTA: Send Bluwat your concrete wash water solids separation sample, current treatment sequence, water or sludge analysis, separator type and performance target. The technical team can recommend a short list of BLUFLOC grades for jar testing, provide a sample and support the transition from laboratory screening to a controlled plant trial. |










