- Plant-Based Deodorant
- Water Treatment Chemicals
- Coagulant
-
Flocculant
- Polyacrylamide for Textile, Food & Process Industries
- Polyacrylamide for Oil, Gas & Drilling
- Polyacrylamide for Pulp&Paper
- Polyacrylamide for Mining & Mineral Processing
- Polyacrylamide for Sludge Dewatering
- Polyacrylamide for Water & Wastewater Clarification
- Polyacrylamide Emulsion
- Polyacrylamide Powder
- BWD-01 Water Decoloring Agent
Anionic Polyacrylamide APAM pH 6-8 in 1% Solution for Sugar Mill Filter Mud Settling and Dewatering CAS 9003-05-8 ISO 9001 Manufacturer 750kg Net Big Bag
Product Overview
In sugar clarification and mud handling, polymer purchasing should begin with the real separation problem rather than a generic request for PAM. This page addresses filter mud containing bagasse fibers, lime and clarification precipitates. The objective is to create a floc that matches the hydraulic loading, shear and drainage mechanism of the mud settler, rotary vacuum filter, belt press or filter press. Anionic Polyacrylamide provides long polymer chains that connect destabilized particles into larger aggregates; the anionic chain is commonly evaluated for bridging mineral-rich or positively conditioned solids. The result can be faster water release and improved solids capture when grade, preparation and dose are correct.
PAM is not a complete treatment train. It acts on suspended and colloidal material that is already available for flocculation. Dissolved contaminants, stable emulsions, incompletely precipitated metals and uncontrolled pH require the appropriate upstream process. This boundary is particularly important when a visually clear filtrate can still contain dissolved COD, color, oil or metals.

Sludge Dewatering Problem
The relevant feed is filter mud containing bagasse fibers, lime and clarification precipitates. The main operating difficulty is that fine mineral-organic particles settle slowly and can carry valuable sugar-bearing liquor into a wet mud cake. A weak program allows fines to escape and increases recycle loading. An excessive program may create slippery water, sticky cake, belt or cloth blinding, poor release and unnecessary chemical cost. The practical target is therefore not the largest floc in a beaker; it is faster mud settling, clearer overflow, improved filtration and better water or process-liquor recovery.
APAM should be screened against the actual juice clarification chemistry, temperature and pH; avoid treating it as a universal sugar-process dosage.
How APAM Supports the Separation Process
- Particle contact: The prepared APAM solution disperses through the conditioned sludge so charged sites and suspended particles can contact the polymer chain.
- Charge response: The selected charge level reduces electrostatic stability where applicable. Charge demand depends on sludge source, upstream coagulants, pH, salts and soluble organics.
- Polymer bridging: Extended chains connect multiple particles into floc that is large enough to retain but open enough to release water.
- Equipment separation: The mud settler, rotary vacuum filter, belt press or filter press uses the gravity, pressure or centrifugal separation mechanism selected by the plant to separate the conditioned solids from the released liquid.
- Controlled optimization: Dose, solution concentration, mixing energy and injection point are adjusted together while the operator monitors capture, cake quality and equipment capacity.
Recommended Addition Point and Equipment Fit
Introduce the fully activated polymer at the following location: after clarification chemistry has formed the solids, before settling and final water removal. The point must provide uniform contact without exposing newly formed floc to unnecessary high shear. Where an inline mixer is used, begin with the minimum energy needed to distribute the solution. Where a flocculation tank is available, observe whether floc continues to grow or begins to break before it reaches the equipment.
For the mud settler, rotary vacuum filter, belt press or filter press, the operator should judge polymer performance together with feed solids, hydraulic load and machine settings. A polymer change can improve conditioning, but it cannot correct worn separation surfaces, blocked drainage paths, unsuitable mechanical settings, poor feed equalization or an overloaded machine.
Grade Selection Guidance
BLUFLOC APAM is available across a 5-25 million molecular-weight range and 5-100% anionic-degree range. For this mineral-rich application, screen more than one molecular weight and anionic degree because residual lime, alum, temperature and surface charge change the bridging response. APAM is the intended search product for this page, but a side-by-side ionic screening is appropriate if the sample produces weak or inconsistent floc.
- Test fresh, representative sludge at the normal feed-solids concentration.
- Keep upstream chemistry and mechanical settings constant during each comparison.
- Compare at least three doses for each candidate grade.
- Prefer the lowest dose that achieves the required capture, drainage and cake handling.
- Confirm the selected grade in a continuous equipment trial before bulk purchasing.
BLUFLOC Powder PAM Typical Supply Range
| Property | Specified Range | Practical Relevance |
|---|---|---|
| Appearance | Off-white granular powder | Dry, free-flowing product when correctly stored |
| Ionic type | Anionic | Select by sludge surface chemistry and jar testing |
| Particle size | 20-100 mesh | Supports controlled dry-powder make-down |
| Molecular weight | 5-25 million | Screen grades for floc size, drainage and shear environment |
| Charge range | 5-100% anionic degree | Match the charge demand of the actual sludge |
| Solid content | 89% minimum | Use active-product basis for cost and dose comparisons |
| Bulk density | About 0.8 | Useful for storage and feeder planning |
| Residual monomer | 0.05% maximum | TDS quality-control limit |
| Working concentration | 0.1-0.5% | Select dilution for activation, pumping and dispersion |
| pH of 1% solution | 6-8 | Product-solution property, not a required sludge operating pH |
| Storage temperature | 0-35°C | Keep dry, shaded and protected from moisture |
| Shelf life | 2 years | Applies under appropriate storage conditions |
Technical values are taken from the supplied BLUFLOC Polyacrylamide Powder TDS. Final grade and dose must be confirmed using representative sludge and the actual equipment.
Polymer Solution Preparation
- Fill a clean make-down tank with suitable water and start moderate agitation before adding powder.
- Meter the dry powder slowly and evenly into the moving water. Avoid dumping the product, which forms fish-eyes or gel lumps.
- Prepare a 0.1-0.5% solution. Choose the lower end where easier dispersion and accurate low-dose control are important; choose a higher concentration only when the system can mix, pump and dilute it reliably.
- Agitate at approximately 200-400 rpm for about one hour. Excessive mixer speed can cut polymer chains and reduce performance.
- Inspect the solution for undissolved particles before use. Keep the solution tank, transfer pump and dosing line clean and free of incompatible chemical residues.
- At the application point, dilute further when needed to improve distribution across the sludge stream. Do not combine concentrated PAM directly with coagulant in the same make-down tank.
Bench Test and Equipment Trial
- Collect the sludge during representative sugar clarification and mud handling operation and record source, temperature, pH, feed solids and upstream chemical additions.
- Prepare fresh APAM solutions at a known concentration and screen several charge or molecular-weight options.
- Run a dose-response series with equal mixing. Observe initial floc formation, free-water release, supernatant clarity and resistance to gentle shear.
- Take the strongest candidates to the mud settler, rotary vacuum filter, belt press or filter press. Keep feed rate and mechanical settings steady long enough to compare each condition.
- Record settling rate, mud-bed compaction, overflow clarity, filter throughput, cake moisture and sugar loss. Convert consumption to active polymer per tonne of dry solids whenever the feed-solids data allow.
- Repeat the test under a second representative operating condition before approving the product and create a dose curve for routine control.
Operating Performance Indicators
| Solids capture | Measures whether fine particles remain with the cake rather than returning in filtrate, centrate or overflow. |
| Cake or underflow solids | Shows the mass and transport impact of water removal; compare on a consistent sampling basis. |
| Liquid quality | Track suspended solids and any process-specific parameter such as color, FOG or metals. |
| Equipment capacity | Assess feed rate, cycle time, torque, belt speed or hydraulic loading as applicable. |
| Specific polymer use | Report active polymer against dry solids, not only pump speed or solution volume. |
| Total operating cost | Balance polymer, energy, wash water, labor, throughput and sludge disposal rather than minimizing one item alone. |
Troubleshooting
Poor results can arise from inadequate lime or clarification control. Optimize the primary process first, then select APAM by jar testing.
| Small or weak floc | Verify complete dissolution, increase contact gently, review charge demand and test another grade. |
| Cloudy filtrate or centrate | Check underdosing, high shear, feed-solids change, injection location and equipment loading. |
| Sticky or gelatinous sludge | Reduce dose, improve dilution and dispersion, and check for undissolved polymer or high grease. |
| Good jar test, poor machine result | Reproduce actual shear, residence time and dilution; inspect the transfer path and mechanical settings. |
| Rising polymer consumption | Measure feed solids, source blending, pH, conductivity, upstream chemical changes and sludge age. |
Packaging and Storage
This buyer-intent configuration specifies 750 kg net big bag. The TDS also lists 25 kg kraft-paper or PE bags with inner plastic liners and 750 kg net big bags. Store unopened product in a dry, shaded area at 0-35°C. Protect it from moisture because dry PAM becomes extremely slippery when wet and partially hydrated powder can form difficult lumps. Use suitable dust control and follow the current SDS and site handling procedures. The stated shelf life is two years under appropriate storage conditions.
Why Source BLUFLOC PAM from Bluwat Chemicals
- Anionic, cationic and nonionic powder ranges for comparative application screening.
- Technical discussion based on sludge source, upstream chemistry and dewatering equipment.
- Jar-test samples available for grade and dose evaluation.
- 25 kg bags and 750 kg net big bags for trial, routine consumption and bulk handling needs.
- Manufacturer management-system positioning referenced as ISO 9001.
- Export experience serving water, wastewater and process-industry customers in multiple markets.
Frequently Asked Questions
Is APAM always the correct polymer for this sludge?
No. APAM is the intended starting product for this search, but actual particle charge, upstream chemicals and equipment shear determine the best ionic type and grade. Comparative testing is required.
Does the solution pH in the title define the sludge operating pH?
No. The stated pH is the TDS value for a 1% APAM solution. It is not a universal process set point. Adjust sludge pH according to upstream treatment chemistry and the contaminants being controlled.
What working-solution concentration should the plant prepare?
The supplied TDS recommends 0.1-0.5%. The final concentration should suit the make-down unit, dosing-pump range, dilution water and required dispersion at the application point.
How should dose be compared on the mud settler, rotary vacuum filter, belt press or filter press?
Use active polymer per tonne of dry solids and compare it with capture, cake solids, throughput and liquid quality.
Can PAM solve poor precipitation, color removal or emulsion breaking?
No. Complete those upstream reactions first. PAM mainly enlarges and captures suspended or precipitated solids so that the dewatering equipment can separate them.
Request a Sludge Dewatering Evaluation
Send Bluwat Chemicals the sludge source, daily wet-sludge flow, feed-solids concentration, current polymer and dose, upstream coagulants, mud settler, rotary vacuum filter, belt press or filter press model or capacity, current cake solids, filtrate or centrate quality and the main operating problem. We can then narrow the BLUFLOC APAM screening range and propose a bench-to-equipment trial plan.










