BWD-01 Cationic Color Removal Polymer for Denim and Garment Washing Wastewater in Mexico

Product Overview

Textile wet processing in Mexico does not create one uniform wastewater. Fiber type, dye class, shade depth, washing recipe and finishing chemistry can change the color and charge demand from one production batch to the next.

BWD-01 supplies strong cationic charge to destabilize negatively charged soluble dyes and fine color-bearing particles. It is especially relevant to denim-associated color, reactive dyes and printing pigments. The objective is not merely to make the sample look clearer, but to produce flocs that can be separated reliably by sedimentation or dissolved-air flotation.

Textile Wastewater Problem in Mexico

The central treatment problem is that wash recipes, lint and concentrated color releases cause unstable clarification and sludge production. Conventional inorganic coagulation may remove suspended solids but leave a visible soluble-color fraction. Operators may then increase coagulant dose, creating more sludge without proportional color improvement.

Why the Problem Occurs

• Garment washing releases fibers and color-bearing particles.
• Detergents, enzymes and finishing agents can change floc characteristics.
• Rapid product changes create a wide range of shade and CODcr conditions.

BWD-01 Treatment Solution

Use effective screening and equalization, then apply BWD-01 to the remaining color fraction with PAC order confirmed by jar testing.

The selected program should be based on actual wastewater rather than a universal dose. A controlled jar test identifies the point where charge neutralization, floc formation, separation speed and sludge production are balanced. PAC can be tested before or after BWD-01, but the two products must be prepared and dosed separately.

Technical Specifications

Technical note: Values are based on the Bluwat BWD-01 TDS. Confirm the supplied batch with its Certificate of Analysis and consult the SDS for handling and shelf-life details.

Recommended Application Scenarios

• Denim washing and garment-finishing wastewater.
• Cotton reactive-dye and rinse effluent.
• Textile-printing and mixed apparel wastewater.

How BWD-01 Works

1. Charge neutralization: cationic groups interact with negatively charged denim-associated color, reactive dyes and printing pigments and colored colloids.
2. Destabilization: reduced electrostatic repulsion allows dissolved or finely dispersed color bodies to associate.
3. Floc formation: the destabilized contaminants form visible aggregates; PAC may strengthen or densify flocs where testing supports it.
4. Solid-liquid separation: the resulting flocs are removed by sedimentation or air flotation, producing clearer treated water.

How to Choose and Test BWD-01

• Remove coarse lint before calculating chemical demand.
• Compare sedimentation and DAF where both are available.
• Evaluate total treatment cost including sludge handling.

Use untreated and current-treatment controls in every jar-test series. Record raw-water pH, true or apparent color, CODcr, turbidity, temperature and production source. Photographs are useful, but analytical results and sludge behavior are required for a defensible selection.

Recommended Application Procedure

1. Collect a representative wastewater sample after appropriate screening and equalization.
2. Prepare several BWD-01 working solutions by diluting the product with 10 to 40 times clean water.
3. Use pH 7.5-8.0 as the TDS starting range for improved performance, then test nearby values if necessary.
4. Dose BWD-01 into the wastewater and mix thoroughly for several minutes.
5. Where color and CODcr remain high, test PAC before and after BWD-01 in separate beakers. Do not premix the chemicals.
6. Allow the flocs to settle or evaluate them by dissolved-air flotation, matching the site's full-scale process.
7. Compare final color, CODcr, turbidity, floc strength, separation time, sludge volume and total treatment cost before scale-up.

Expected Treatment Results

The BWD-01 TDS reports typical decolorization of approximately 50%-99% and CODcr reduction of approximately 50%-80% in suitable applications. These are reference ranges, not guaranteed results. Actual performance depends on dye class, concentration, auxiliaries, pH, mixing, chemical sequence and separation equipment.

Compared with a high-dose inorganic-only program, BWD-01 may provide faster flocculation and settling and may reduce the inorganic contribution to sludge. The comparison should use dry solids, dewatering behavior and disposal cost where sludge reduction is a project objective.

Bluwat Manufacturing Advantages

• Manufacturer since 2000 with more than 25 years of water-treatment chemical production and export experience.
• Three production bases supporting stable supply, batch control and multiple packaging options.
• Products exported to more than 80 countries and used by over 5,000 industrial customers.
• Quality and environmental systems including ISO 9001 and ISO 14001, with ZDHC-conformant BWD product support.
• Routine control of appearance, solid content, specific gravity, pH, viscosity and solubility, supported by batch COA.
• Free sample availability and technical support for jar-test design, dosage comparison and full-scale trial planning.
• Standard BWD-01 packaging in 30 kg and 250 kg plastic drums or 1250 kg IBC containers.

For customers in the Americas, Bluwat supports sample evaluation, container-load planning, stable batch specifications and technical communication for distributors, textile groups and individual mills.

Frequently Asked Questions