- Plant-Based Deodorant
- Water Treatment Chemicals
- Coagulant
-
Flocculant
- Polyacrylamide for Textile, Food & Process Industries
- Polyacrylamide for Oil, Gas & Drilling
- Polyacrylamide for Pulp&Paper
- Polyacrylamide for Mining & Mineral Processing
- Polyacrylamide for Sludge Dewatering
- Polyacrylamide for Water & Wastewater Clarification
- Polyacrylamide Emulsion
- Polyacrylamide Powder
- BWD-01 Water Decoloring Agent
BWF160 Silicone Defoamer for Industrial Water Treatment Systems
Foam can form in equalization, reaction, recirculation and discharge sections when surfactants, organics and mechanical agitation are present.
BWF160 is positioned as a general-purpose silicone defoamer for water-based treatment processes where rapid foam knockdown and continued suppression are both required.
In industrial water treatment systems, uncontrolled foam is not only a visual issue. It can reduce usable tank volume, cause overflow, contaminate walkways, interfere with level instruments and carry solids or liquid into downstream units. A suitable defoamer should therefore be assessed for both immediate foam collapse and resistance to re-foaming under real mixing, pumping or aeration conditions.
BWF160 should be treated as one component of process control. Operators should also investigate the underlying source of foam, including surfactant loading, production changes, biological conditions, aeration intensity, recycle streams and hydraulic turbulence.
- Fast initial defoaming for active surface foam.
- Continued foam suppression under water-based process conditions.
- Nonionic formulation for broad site-specific compatibility evaluation.
- Easy dispersion with no floating-oil appearance when properly selected and applied.
- Flexible direct, drip, spray or turbulent-inlet dosing options.
- Designed for water-treatment use and described as not causing secondary water pollution under intended application.

| Property | Specification / Description |
| Product model | BWF160 |
| Product type | Water-treatment silicone defoamer / antifoam emulsion |
| Active composition | Polysiloxane with synergist, emulsifier and dispersant |
| Appearance | Milky-white flowable liquid |
| Ionic character | Nonionic |
| pH | 6-8 |
| Non-volatile content | 12-20% |
| Centrifugal stability | No separation after 3,000 rpm for 20 minutes |
| General reference dosage | Approximately 50-300 ppm, subject to actual foam conditions |
| Optional pre-dilution | Clean cold water; 1-3-fold dilution for drip or spray application |
| Packaging | 25 kg or 200 kg plastic drums |
| Shelf life | One year under normal-temperature storage; protect from freezing |
The general reference dosage is approximately 50-300 ppm. This is a screening range rather than a guaranteed fixed dose. Actual demand depends on surfactant type, contaminant concentration, temperature, pH, dissolved and suspended solids, aeration, mixing energy and the required duration of control.
BWF160 can be added directly at an inlet with good wastewater turbulence. Where broad surface contact is needed, it may be pre-diluted with clean cold water at a 1-3-fold dilution and applied by drip or spray to the foam-concentrated area. Use clean equipment and avoid preparing more diluted product than the operation can use promptly.
- Record the untreated foam height and operating conditions.
- Start at a conservative dose and increase stepwise.
- Measure both collapse time and the interval before foam returns.
- Track overflow frequency, usable tank volume, downstream carryover and total daily consumption.
- Confirm that clarification, biological treatment, filtration or discharge performance remains acceptable.
Evaluate the product at the most turbulent inlet, recirculation return or concentrated foam zone. The best point is normally upstream of overflow risk but after the main source of air entrainment is known.
When PAC, PolyDADMAC, polyamine, decoloring agent or polyacrylamide is also used, conduct a compatibility trial with the full treatment sequence. Foam reduction should not be evaluated in isolation from floc formation, settling, flotation, sludge dewatering or final-water quality.
BWF160 is packed in 25 kg or 200 kg plastic drums. Store sealed containers at normal temperature in accordance with general chemical-storage practice. The stated shelf life is one year. Protect the product from freezing, rotate stock on a first-in-first-out basis and inspect emulsion appearance before use after extended storage.
Bluwat Chemicals supplies water-treatment chemicals for industrial and municipal applications. The commercial approach combines product selection, sample evaluation and application discussion so that buyers can qualify a grade against their own water, equipment and treatment objectives. For a new project, provide the wastewater source, current process, daily flow, foam location, temperature, pH and any existing defoamer information to support a more relevant recommendation.
Is BWF160 a silicone defoamer?
A: Yes. The supplied information describes a polysiloxane-based formulation with synergist, emulsifier and dispersant.
Can BWF160 be diluted before dosing?
A: Yes. Clean cold water can be used for a 1-3-fold pre-dilution when drip or spray distribution is preferred. Confirm the practical dilution procedure on site.
What is the recommended dosage?
A: A general reference range is approximately 50-300 ppm. The optimum dose must be established using the actual foaming water and operating conditions.
Can it be used in biological wastewater treatment?
A: The product is described for municipal biological treatment systems and as not affecting activated-sludge bacterial reproduction under intended use. A controlled site trial and routine biological monitoring are still recommended.
How should it be stored?
A: Keep the sealed drums at normal temperature, protect them from freezing and use first-in-first-out stock rotation. The stated shelf life is one year.
