request to quote
Leave Your Message
Cationic Polyacrylamide CPAM 0.05% Max Residual Monomer for Recycled Paper Mill Wet-End Treatment CAS 9003-05-8 ISO 9001 Manufacturer 750kg Net Big Bag
Polyacrylamide for Pulp&Paper
Products Categories
Featured Products

Cationic Polyacrylamide CPAM 0.05% Max Residual Monomer for Recycled Paper Mill Wet-End Treatment CAS 9003-05-8 ISO 9001 Manufacturer 750kg Net Big Bag

BLUFLOC CPAM has a stated residual-monomer limit of 0.05% maximum and can be screened for recycled-paper retention and drainage programs. Match the grade to furnish charge and contaminants. The monomer specification does not establish food-contact approval for the finished paper.

    Product Overview

    BLUFLOC CPAM is a candidate polymer for retention and drainage control in recycled-paper wet ends. It should be evaluated against the mill's actual furnish variability and existing contaminant-control program.

    The stated residual-monomer limit is 0.05% maximum. This is a product-quality specification; it does not replace a regulatory assessment of the grade or establish suitability for food-contact paper.

    Cause

    Recycled furnish introduces varying amounts of fines, ash, dissolved anionic substances and adhesive contaminants. Some of these components compete with fibers for cationic polymer, making a fixed retention dose less predictable.

    Retention CPAM and contaminant-control chemicals perform related but different functions. Increasing a high-molecular-weight retention polymer to compensate for all anionic demand can lead to poor formation or excessive chemical consumption.

    Solution

    Separate the retention problem from the conditioning problem during laboratory work. Test the existing contaminant-control or fixation step first, then evaluate CPAM retention performance within that defined program.

    Compare furnish charge, first-pass retention, drainage and sheet formation over representative recycled-fiber conditions. Review deposits and runnability during a machine trial, because a clearer white-water sample alone does not show that adhesive contaminants are controlled.

    polyacrylamide for papermaking application.jpg

    Specifications

    Parameter Series specification
    Product series BLUFLOC polyacrylamide powder
    Ionic type Cationic polyacrylamide
    Appearance Off-white granular powder
    Particle size 20–100 mesh
    Molecular weight 5–12 million; grade-dependent
    Cationic charge degree 5–80%; grade-dependent
    Solids content 89% minimum
    Residual monomer 0.05% maximum
    Recommended working solution 0.1–0.5%
    pH of 1% aqueous solution 4–6
    Storage temperature 0–35 °C
    Shelf life 2 years under suitable storage conditions
    Selected packaging 750 kg net big bag
    PAM CAS reference 9003-05-8

    Application

    This page serves recycled-paper machines selecting a powder retention polymer for the wet end. It is relevant to mills handling recovered-paper blends with changing contamination and fines loads.

    Bulk supply in a 750 kg bag suits sites with appropriate unloading and make-down systems. Storage and preparation capacity must accommodate production demand without shortening the required dissolution time.

    How It Works

    CPAM can attach to suitable negative sites and bridge fiber-associated particles into aggregates. Dissolved anionic material may consume part of its charge before the polymer reaches the desired solids.

    A compatible conditioning step can change this competition. The complete program determines polymer efficiency, so neither residual monomer nor cationic charge alone predicts retention performance.

    How To Choose

    Request grade-specific specifications and residual-monomer documentation during supplier qualification. For application screening, provide furnish samples, charge-demand data where available, pH, conductivity and the chemical addition order.

    Compare grades at defined doses and hold conditioning chemistry constant. Check performance across ordinary furnish variations before confirming a supply grade. If the paper has food-contact requirements, obtain the appropriate separate documentation for the product, dosage and intended market rather than relying on the monomer limit.

    Solution Preparation and Storage

    Prepare a 0.1–0.5% solution by gradually feeding the powder into clean water with controlled agitation. On an as-supplied product basis, this is 1–5 g of powder per kg of final solution. Keep the concentration definition consistent throughout grade comparisons.

    The TDS gives about one hour for dissolution and 200–400 rpm as preparation guidance. Actual dissolution time depends on polymer type, water quality, temperature and mixing. Adjust agitation for the tank and impeller; avoid excessive shear that can damage polymer chains.

    Check for undissolved granules and gel lumps before dosing. Keep powder dry, protect it from sunlight and store within 0–35 °C. Follow the grade SDS for handling; clean polymer spills promptly because wet polymer can create slippery surfaces.

    Disperse the matured solution uniformly at the tested wet-end addition point. Further dilution for delivery may be useful if the make-down and dosing equipment require it; verify the final program on the machine.

    FAQ

    Does the 0.05% monomer limit prove food-contact compliance?

    No. Food-contact suitability requires separate evidence for the specific product, use conditions and jurisdiction. A residual-monomer specification is only one product-quality characteristic.

    Can retention CPAM replace every anionic-trash control chemical?

    No. High-molecular-weight retention polymers and conditioning chemicals have different roles. Test the complete program rather than treating them as interchangeable.

    Why does a recycled furnish need repeated sampling?

    Contaminant and fines loads can vary with the recovered-paper supply. Representative samples reveal whether the selected polymer remains useful under normal operating changes.

    Supplier Documentation and Grade Enquiry

    Bluwat Chemicals supplies BLUFLOC powder polymers in anionic, cationic and nonionic grades. For supplier qualification, request the selected grade TDS, SDS, batch COA and current ISO 9001 documentation. Send the process information listed above when requesting a sample or grade recommendation.

    Leave Your Message