request to quote
Leave Your Message
Cationic Polyacrylamide CPAM 0.1-0.5% Working Solution for Paper Making Retention and Drainage Aid CAS 9003-05-8 ISO 9001 Manufacturer 25kg Kraft Paper Bag
Polyacrylamide for Pulp&Paper
Products Categories
Featured Products

Cationic Polyacrylamide CPAM 0.1-0.5% Working Solution for Paper Making Retention and Drainage Aid CAS 9003-05-8 ISO 9001 Manufacturer 25kg Kraft Paper Bag

BLUFLOC CPAM is a cationic polyacrylamide powder for evaluating fiber and filler retention alongside paper-stock drainage. Prepare a 0.1–0.5% solution and select the grade using furnish-specific retention, drainage and formation tests. Supplied in 25 kg kraft paper bags with an inner plastic liner.

    Product Overview

    BLUFLOC cationic polyacrylamide is a candidate retention and drainage aid when fibers, fines and filler escape through the forming fabric. The objective is a balanced wet-end program: retain useful solids while allowing water to leave the sheet without unacceptable loss of formation.

    The recommended 0.1–0.5% working concentration describes the prepared polymer solution. It does not specify the dose on dry paper stock or promise a particular retention increase.

    Cause

    Short fibers and fine mineral particles may be too small to remain in the developing fiber mat. Changes in furnish composition, anionic trash and the existing chemical program can also alter polymer adsorption and cause unstable white-water solids.

    Increasing polymer feed alone can create oversized flocs. These may drain differently but leave an uneven sheet, so retention, drainage and formation must be assessed together.

    polyacrylamide for papermaking application.jpg

    Solution

    Screen CPAM grades using representative machine furnish and the current wet-end additives. Compare first-pass total retention, ash retention and drainage under a defined mixing and shear sequence before selecting a mill trial candidate.

    Place the addition point where the solution disperses evenly and the subsequent shear suits the program. A CPAM-only program and a program with a compatible microparticle require separate evaluation; their addition sequences are not interchangeable.

    Specifications

    Parameter Series specification
    Product series BLUFLOC polyacrylamide powder
    Ionic type Cationic polyacrylamide
    Appearance Off-white granular powder
    Particle size 20–100 mesh
    Molecular weight 5–12 million; grade-dependent
    Cationic charge degree 5–80%; grade-dependent
    Solids content 89% minimum
    Residual monomer 0.05% maximum
    Recommended working solution 0.1–0.5%
    pH of 1% aqueous solution 4–6
    Storage temperature 0–35 °C
    Shelf life 2 years under suitable storage conditions
    Selected packaging 25 kg kraft paper bag with inner plastic liner
    PAM CAS reference 9003-05-8

    Application

    This page addresses the paper-machine wet end in mills seeking to control fiber and filler losses. It is relevant to furnishes containing chemical pulp, recycled fiber or mineral filler, provided laboratory testing confirms adsorption and acceptable sheet formation.

    White-water clarification downstream is a separate application. Its best polymer grade and dosage may differ from the grade selected for the forming section.

    How It Works

    Cationic groups promote adsorption onto negatively charged fiber surfaces. Extended polymer chains can bridge fines, filler and fibers into aggregates that are more readily retained in the mat.

    The resulting structure can influence drainage paths. The final effect depends on floc size, shear history and stock chemistry rather than molecular weight alone.

    How To Choose

    Begin with furnish consistency, pH, conductivity, ash content and measured charge demand. Screen more than one charge level within the CPAM series, then vary molecular weight and feed rate while keeping the other chemicals constant.

    Use a dynamic drainage or retention test that represents the machine's shear. Reject a candidate if its retention benefit is accompanied by poor formation or unstable operation. Express trial dosage on a clearly defined dry-furnish basis and verify it on the machine.

    Solution Preparation and Storage

    Prepare a 0.1–0.5% solution by gradually feeding the powder into clean water with controlled agitation. On an as-supplied product basis, this is 1–5 g of powder per kg of final solution. Keep the concentration definition consistent throughout grade comparisons.

    The TDS gives about one hour for dissolution and 200–400 rpm as preparation guidance. Actual dissolution time depends on polymer type, water quality, temperature and mixing. Adjust agitation for the tank and impeller; avoid excessive shear that can damage polymer chains.

    Check for undissolved granules and gel lumps before dosing. Keep powder dry, protect it from sunlight and store within 0–35 °C. Follow the grade SDS for handling; clean polymer spills promptly because wet polymer can create slippery surfaces.

    Disperse the matured solution uniformly at the tested wet-end addition point. Further dilution for delivery may be useful if the make-down and dosing equipment require it; verify the final program on the machine.

    FAQ

    Is 0.1–0.5% the dose in the paper stock?

    No. It is the polymer solution concentration before dosing. The amount added to stock must be determined separately and reported on a defined dry-furnish basis.

    Can one CPAM grade suit every paper machine?

    No. Furnish charge, filler chemistry, conductivity and shear differ between machines. A grade should pass retention, drainage and formation checks on the intended furnish.

    What should a mill send for grade selection?

    Provide a representative furnish sample, current chemical sequence, stock consistency, pH, conductivity and the main production problem. Include baseline retention and drainage results where available.

    Supplier Documentation and Grade Enquiry

    Bluwat Chemicals supplies BLUFLOC powder polymers in anionic, cationic and nonionic grades. For supplier qualification, request the selected grade TDS, SDS, batch COA and current ISO 9001 documentation. Send the process information listed above when requesting a sample or grade recommendation.

    Leave Your Message