request to quote
Leave Your Message
Cationic Polyacrylamide CPAM 5-12 Million MW 89% Min Solid for Paper Stock Drainage Improvement CAS 9003-05-8 ISO 9001 Manufacturer 25kg PE Bag
Polyacrylamide for Pulp&Paper
Products Categories
Featured Products

Cationic Polyacrylamide CPAM 5-12 Million MW 89% Min Solid for Paper Stock Drainage Improvement CAS 9003-05-8 ISO 9001 Manufacturer 25kg PE Bag

BLUFLOC CPAM grades span a molecular-weight range of 5–12 million with at least 89% solids. They can be screened for paper-stock drainage while monitoring retention and formation. Molecular weight is a selection variable rather than a guarantee of faster machine production.

    Product Overview

    BLUFLOC CPAM is a drainage-aid candidate when paper stock releases water poorly because of its fines content and wet-end chemistry. The selected grade should improve the relevant drainage behavior while maintaining solids retention and acceptable formation.

    The CPAM series has a stated molecular-weight range of 5–12 million. Choose an individual grade within that range through testing; the highest value is not automatically the best option.

    Cause

    Refining, recycled fines and filler can change the pore structure of the forming mat. A dense fines layer may impede water movement even when the stock appears well dispersed before sheet formation.

    Poor drainage can also come from mechanical restrictions, vacuum conditions or furnish changes. Chemical testing should therefore distinguish a polymer-responsive problem from an equipment bottleneck.

    Solution

    Compare candidate CPAM grades using the same stock consistency, temperature and mixing history. Measure drainage time or filtrate release with the existing retention chemistry present, and record solids in the filtrate.

    Take promising candidates into handsheet and machine trials. Monitor formation, press-section behavior and operating stability before attributing a production change to CPAM. A faster laboratory filtrate flow alone does not establish higher machine speed.
    polyacrylamide for papermaking application.jpg

    Specifications

    Parameter Series specification
    Product series BLUFLOC polyacrylamide powder
    Ionic type Cationic polyacrylamide
    Appearance Off-white granular powder
    Particle size 20–100 mesh
    Molecular weight 5–12 million; grade-dependent
    Cationic charge degree 5–80%; grade-dependent
    Solids content 89% minimum
    Residual monomer 0.05% maximum
    Recommended working solution 0.1–0.5%
    pH of 1% aqueous solution 4–6
    Storage temperature 0–35 °C
    Shelf life 2 years under suitable storage conditions
    Selected packaging 25 kg PE bag
    PAM CAS reference 9003-05-8

    Application

    This evaluation is relevant to stock preparation and the forming section of paper or board machines. It is particularly useful when furnish changes create a new balance between fines retention and water release.

    The purpose is stock drainage improvement. Sludge dewatering uses different feed materials and equipment, so its polymer test results should not substitute for wet-end drainage trials.

    How It Works

    CPAM can adsorb onto negative fiber sites and bridge fine material into a more organized network. This may reduce the accumulation of dispersed fines in flow paths through the forming mat.

    Floc structure must remain compatible with sheet formation. Excessive bridging can produce coarse patches, demonstrating why drainage and paper uniformity should be measured together.

    How To Choose

    Start with stock freeness, fines level, consistency, filler content and charge demand. Screen charge and molecular weight independently where suitable grades are available, rather than choosing solely by the 5–12 million range.

    Compare results at equal and clearly defined product doses. Select a candidate only if drainage gains persist under realistic shear and sheet properties remain acceptable. During a machine trial, document vacuum settings and furnish conditions so mechanical changes do not obscure the chemical response.

    Solution Preparation and Storage

    Prepare a 0.1–0.5% solution by gradually feeding the powder into clean water with controlled agitation. On an as-supplied product basis, this is 1–5 g of powder per kg of final solution. Keep the concentration definition consistent throughout grade comparisons.

    The TDS gives about one hour for dissolution and 200–400 rpm as preparation guidance. Actual dissolution time depends on polymer type, water quality, temperature and mixing. Adjust agitation for the tank and impeller; avoid excessive shear that can damage polymer chains.

    Check for undissolved granules and gel lumps before dosing. Keep powder dry, protect it from sunlight and store within 0–35 °C. Follow the grade SDS for handling; clean polymer spills promptly because wet polymer can create slippery surfaces.

    FAQ

    Will higher molecular weight always improve drainage?

    No. Chain length affects bridging, but excessive flocculation can harm formation. Evaluate charge, dose and shear alongside molecular weight.

    Can CPAM correct a mechanical drainage limitation?

    It cannot replace equipment maintenance or vacuum control. Confirm whether the furnish responds to polymer before treating the problem as purely chemical.

    What is the difference between drainage and retention?

    Drainage concerns water release from stock. Retention concerns capture of furnish solids in the sheet. A useful program must balance both rather than optimize one in isolation.

    Supplier Documentation and Grade Enquiry

    Bluwat Chemicals supplies BLUFLOC powder polymers in anionic, cationic and nonionic grades. For supplier qualification, request the selected grade TDS, SDS, batch COA and current ISO 9001 documentation. Send the process information listed above when requesting a sample or grade recommendation.

    Leave Your Message