- Plant-Based Deodorant
- Water Treatment Chemicals
- Coagulant
-
Flocculant
- Polyacrylamide for Textile, Food & Process Industries
- Polyacrylamide for Oil, Gas & Drilling
- Polyacrylamide for Pulp&Paper
- Polyacrylamide for Mining & Mineral Processing
- Polyacrylamide for Sludge Dewatering
- Polyacrylamide for Water & Wastewater Clarification
- Polyacrylamide Emulsion
- Polyacrylamide Powder
- BWD-01 Water Decoloring Agent
Cationic Polyacrylamide CPAM 5-12 Million MW 89% Min Solid for Plate and Frame Filter Press Dewatering CAS 9003-05-8 ISO 9001 Manufacturer 25kg Kraft Paper Bag
Product Overview
In industrial sludge treatment, polymer purchasing should begin with the real separation problem rather than a generic request for PAM. This page addresses fine suspended solids requiring batch plate-and-frame pressure filtration. The objective is to create a floc that matches the hydraulic loading, shear and drainage mechanism of the plate and frame filter press. Cationic Polyacrylamide provides long polymer chains that connect destabilized particles into larger aggregates; the cationic charge also helps neutralize many negatively charged organic and biological surfaces. The result can be faster water release and improved solids capture when grade, preparation and dose are correct.
PAM is not a complete treatment train. It acts on suspended and colloidal material that is already available for flocculation. Dissolved contaminants, stable emulsions, incompletely precipitated metals and uncontrolled pH require the appropriate upstream process. This boundary is particularly important when a visually clear filtrate can still contain dissolved COD, color, oil or metals.

Sludge Dewatering Problem
The relevant feed is fine suspended solids requiring batch plate-and-frame pressure filtration. The main operating difficulty is that fine particles and metal hydroxides can create a dense, compressible cake that resists water passage. A weak program allows fines to escape and increases recycle loading. An excessive program may create slippery water, sticky cake, belt or cloth blinding, poor release and unnecessary chemical cost. The practical target is therefore not the largest floc in a beaker; it is strong but permeable floc, short filtration cycles, high solids recovery and predictable cake discharge.
How CPAM Supports the Separation Process
- Particle contact: The prepared CPAM solution disperses through the conditioned sludge so charged sites and suspended particles can contact the polymer chain.
- Charge response: The selected charge level reduces electrostatic stability where applicable. Charge demand depends on sludge source, upstream coagulants, pH, salts and soluble organics.
- Polymer bridging: Extended chains connect multiple particles into floc that is large enough to retain but open enough to release water.
- Equipment separation: The plate and frame filter press uses batch pressure filtration through the filter cloth to separate the conditioned solids from the released liquid.
- Controlled optimization: Dose, solution concentration, mixing energy and injection point are adjusted together while the operator monitors capture, cake quality and equipment capacity.
Recommended Addition Point and Equipment Fit
Introduce the fully activated polymer at the following location: the sludge conditioning tank or a low-shear line before the press, after pH adjustment and inorganic coagulation when required. The point must provide uniform contact without exposing newly formed floc to unnecessary high shear.
Grade Selection Guidance
BLUFLOC CPAM is available across a 5-12 million molecular-weight range and 5-80% charge-degree range. No charge or molecular-weight label should be selected without a comparative test.
- Test fresh, representative sludge at the normal feed-solids concentration.
- Keep upstream chemistry and mechanical settings constant during each comparison.
- Compare at least three doses for each candidate grade.
- Prefer the lowest dose that achieves the required capture, drainage and cake handling.
BLUFLOC Powder PAM Typical Supply Range
| Property | Specified Range | Practical Relevance |
|---|---|---|
| Appearance | Off-white granular powder | Dry, free-flowing product |
| Ionic type | Cationic | Select by sludge chemistry |
| Molecular weight | 5-12 million | Screen for floc size |
| Charge range | 5-80% | Match sludge demand |
| Solid content | 89% minimum | Use active-product basis |
Polymer Solution Preparation
- Fill a clean make-down tank with suitable water and start moderate agitation.
- Meter the dry powder slowly into the moving water to avoid fish-eyes.
- Prepare a 0.1-0.5% solution.
- Agitate at 200-400 rpm for about one hour.
- Inspect for undissolved particles before use.
Operating Performance Indicators
| Indicator | Focus |
|---|---|
| Solids capture | Retention of fine particles |
| Cake solids | Mass and transport impact |
| Liquid quality | Turbidity, color, FOG |
| Equipment capacity | Throughput and cycle time |
Frequently Asked Questions
Is CPAM always the correct polymer?
No. Comparative testing is required based on particle charge and equipment shear.
Can PAM solve poor precipitation or color removal?
No. Complete upstream reactions first; PAM is for flocculating suspended solids.
Request a Sludge Dewatering Evaluation
Send Bluwat Chemicals your sludge source, flow rates, and current operating problems. We can narrow the BLUFLOC CPAM screening range and propose a bench-to-equipment trial plan.










