- Plant-Based Deodorant
- Water Treatment Chemicals
- Coagulant
-
Flocculant
- Polyacrylamide for Textile, Food & Process Industries
- Polyacrylamide for Oil, Gas & Drilling
- Polyacrylamide for Pulp&Paper
- Polyacrylamide for Mining & Mineral Processing
- Polyacrylamide for Sludge Dewatering
- Polyacrylamide for Water & Wastewater Clarification
- Polyacrylamide Emulsion
- Polyacrylamide Powder
- BWD-01 Water Decoloring Agent
Cationic Polyacrylamide CPAM 5-80% Charge Degree for High-Speed Paper Machine Drainage CAS 9003-05-8 ISO 9001 Manufacturer 750kg Net Big Bag
Product Overview
BLUFLOC CPAM can be evaluated where a high-speed paper machine needs more stable stock drainage and solids retention. Grade selection must reflect short contact times, process shear and the mill's existing retention chemistry.
The 5–80% charge-degree range describes available CPAM series grades. It is not a recommended charge setting for every high-speed machine, and it does not establish a target operating speed.
Cause
High flow rates and short residence times can make chemical dispersion and adsorption more demanding. Pumping, screening and other shear stages can change the flocs formed upstream of the headbox.
A program that performs well in a gentle beaker test may respond differently on the machine. Changing conductivity or anionic demand can further disturb adsorption even when the dosing pump remains steady.
Solution
Use laboratory tests with a controlled shear sequence representing the proposed addition location. Compare drainage, first-pass retention and floc behavior after shear rather than measuring only the initial aggregation.
Screen addition points alongside grades. If the machine uses a microparticle program, evaluate its complete sequence with CPAM under representative conditions. Keep machine speed, vacuum settings and furnish stable during each trial period so the polymer response can be interpreted.

Specifications
| Parameter | Series specification |
| Product series | BLUFLOC polyacrylamide powder |
| Ionic type | Cationic polyacrylamide |
| Appearance | Off-white granular powder |
| Particle size | 20–100 mesh |
| Molecular weight | 5–12 million; grade-dependent |
| Cationic charge degree | 5–80%; grade-dependent |
| Solids content | 89% minimum |
| Residual monomer | 0.05% maximum |
| Recommended working solution | 0.1–0.5% |
| pH of 1% aqueous solution | 4–6 |
| Storage temperature | 0–35 °C |
| Shelf life | 2 years under suitable storage conditions |
| Selected packaging | 750 kg net big bag |
| PAM CAS reference | 9003-05-8 |
Application
The intended duty is drainage and retention control on fast-running paper or board machines with constrained contact time. The evaluation can address a new machine, a speed increase or instability after a furnish change.
How It Works
Cationic charge affects adsorption onto fiber and fine-particle surfaces, while polymer chains connect solids through bridging. Process shear can reduce or reorganize those aggregates.
How To Choose
Provide machine speed, stock flow, consistency, filler level, conductivity and chemical addition locations. Compare multiple charge levels and molecular weights under the same test conditions.
Solution Preparation and Storage
Prepare a 0.1–0.5% solution by gradually feeding the powder into clean water with controlled agitation. Keep powder dry, protect it from sunlight and store within 0–35 °C.
FAQ
Is the highest-charge CPAM best for a high-speed machine?
No. Excess charge can change adsorption and disrupt the wet-end balance. Match the charge level to the furnish and the full chemical program.
Why is a shear test necessary?
It helps reproduce what happens between the dosing point and sheet formation. Flocs measured before shear may not represent the aggregates reaching the forming section.
Can CPAM guarantee a machine-speed increase?
No. Speed is limited by several chemical and mechanical factors.
Supplier Documentation and Grade Enquiry
Bluwat Chemicals supplies BLUFLOC powder polymers in anionic, cationic and nonionic grades. For supplier qualification, request the selected grade TDS, SDS, batch COA and current ISO 9001 documentation.










